Best Beer Batter For Halibut Or Chicken Recipes

BEER BATTER HALIBUT

Steps:

• Divide halibut fillet into approximately 1.5" cubes.
• Mix dry ingredients, add beaten egg. Pour beer in until proper consistency. Batter will be smooth and a little runny but thicker than water.
• The remaining beer is yours to enjoy.
• Add oil to frying pan until oil is approximately 1/2 the height of the halibut cubes; heat on medium high until suitable for deep frying.
• Make a test piece:.
• Coat halibut piece in batter, add to oil. Fry for two minutes, then turn with tongs (being very careful of oil spattering) and fry another two minutes. Transfer finished piece to a paper towel covered plate. Split piece with fork to check for doneness, if piece does not split easily and/or middle of halibut piece does not appear to be opaque, adjust cooking time and/or oil temperature to ensure pieces are done.
• When satisfied with cooking time, repeat until all pieces have been cooked (multiple pieces can be put in pan).
• Serve warm with tartar sauce.

BEER BATTER

Steps:

• In a small mixing bowl add flour, egg, garlic powder, and black pepper. Stir in 1 cup beer (you can add more than one cup to obtain your desired texture).

BEER BATTER FOR HALIBUT OR CHICKEN

Steps:

• Heat deep fryer or skillet with vegetable oil deep enough to cover meat to 375.
• Beat egg, and add remaining ingredients.
• Rinse and dry meat on paper towels in order for it to hold batter.
• Dip meat into batter and place in deep fryer or skillet.
• Cook for approx 4 minutes or until golden brown.
• Drain on paper towels.

BEER-BATTERED HALIBUT WITH TARTAR SAUCE

Steps:

• For the tartar sauce: In a bowl, add the parsley, tarragon, shallot, and cornichon. Chop the hard boiled egg by removing the yolk and crumbling it, then dice the white. Add both yolk and whites to the bowl. Add vinegar, salt, mustard, mayonnaise, and a few dashes of hot sauce (or more to taste). Stir to combine and set aside.
• For the beer batter: In a large mixing bowl, mix the cake flour and baking soda with a fork. Slowly pour in the beer, stirring the entire time (it's okay if there are a few lumps). The batter should be thin, falling off the fork easily so it coats the fish, not heavy like pancake batter. Set aside.
• Fry the halibut: Fill a deep heavy-bottomed pan with oil-don't go higher than 2 inches from the rim-and heat to 350 degrees F. Season the halibut with salt on both sides. Test the oil by cooking a few drops of batter; they should float to the surface when the oil's hot enough. Remove these "tester crunchies" with a slotted spoon. One piece at a time, drop the fish into the beer batter, then remove it, letting the excess drip off. Then place it halfway into the oil, letting a crust form for 10 seconds, then releasing it gently into the pan. Repeat with two more pieces (three at a time), so the pan isn't overcrowded and cook each for 3-4 minutes. Remove the fish to a baking sheet fitted with a wire rack to drain any excess oil. Season with flaky sea salt and serve with tartar sauce and lemon wedges.

BEER BATTERED HALIBUT

Steps:

• Pat halibut filets dry and dredge in extra flour. Mix together flour, cornstarch, baking powder and dash of each salt and pepper. Add enough of the beer to make a pancake-like batter. ( Not too runny but thick enough to coat fish). Do not over stir as batter will become tough.
• Coat fish in batter and let extra drip off back into bowl.
• Oil should be preheated at 365.
• Place carefully in hot oil and cook for 8 - 10 minutes until golden in colour and fish is cooked.